How to Replace a Tub
How to Replace a Tub
Blog Article
Are you currently trying to locate help and advice concerning A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't precisely rocket science, yet it does call for solid plumbing, woodworking, and also often, tiling skills. Replacing an old bathtub with a new one is likewise a moderately hard job. If the old tub is readily obtainable, the project can relocate immediately; if you have to open a wall surface to eliminate the old tub and place the brand-new bathtub, the job is a lot harder. In either instance, the task is within a house handyman's skills, although you will certainly require a helper to vacate the old bathtub and embeded in the brand-new one. Ensure you have certified on your own for the task and fit trying it. Rather than working with a professional to take over a halfway-completed task, it is much better to consider utilizing one before you start. Possibilities are you may require an expert plumber to make tube connections.
This post will assist you mount a new bath tub in your restroom if you have actually currently bought a brand-new bathtub as well as do not need to alter the setup of your previous water supply pipelines.
Your tools as well as product checklist should make up the following:
Planning for the Installation
To start with, the sustaining frame provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing faucets can be rather troublesome because of the restricted access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipelines have been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this procedure. As soon as the taps have been removed, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Before moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Using both wood boards under its feet, place the bathtub in the called for setting. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub up until the spirit level reviews level.
To mount taps, fit all-time low of the outermost flexible tap adapter to the suitable supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Switch on the water and examine all joints and brand-new pipework for leakages as well as tighten them if essential. Fill up the bath tub and additionally check the overflow electrical outlet and the regular outlet for leakages.
Finally, take care of the bathroom paneling as defined in the producer's user's manual. Tiling and sealing around the bath tub ought to wait until the tub has been utilized at the very least once as this will certainly resolve it right into its final setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and also the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin making sure that the washing machines remain in area between the tap as well as the sink. Safeguard the tap in place with the manufacturer offered backnut. When the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap ports. The former type must be attached to the tap ends first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to split an inflexible seal, creating the water to penetrate the wall surface in between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your components as well as installations. They are offered in tubes as well as cartridges, as well as can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked newspaper or soft rope. Remember to always fill the bathtub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealer can break relatively very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily offered on the market. It is recommended to fit the tiles making use of waterproof or water resistant sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading about A Step-by-Step Guide to Installing a Bathtub? Give feedback down the page. We'd be interested to see your insights about this write-up. In hopes to see you back again later on. For those who enjoyed reading our blog posting please do not forget to share it. Many thanks for your time spent reading it.
Visit Website Report this page